abrasion loss
英 [əˈbreɪʒn lɒs]
美 [əˈbreɪʒn lɔːs]
磨耗损失
双语例句
- An engineering model on mass abrasion of kinetic energy ( KE) penetrator is presented to predict the nose shape and mass loss of the residual projectile after high speed penetration into concrete.
通过对高速侵彻弹体的质量侵蚀实验现象进行分析，建立了质量侵蚀的工程理论模型，可对动能侵彻弹体头部侵蚀后的头形和质量侵蚀进行预期。 - The abrasion's serious enough to cause loss of consciousness.
擦伤很严重，足以造成失去知觉。 - More seriously, the abrasion to certain extent may cause accidents, then leads to casualties and production loss.
更严重的是，磨损到一定程度后会导致突然事故，造成不必要的人员伤亡和生产损失。 - The influence of grain size distribution on apparent porosity, bulk density, modulus of rupture, crushing strength, abrasion loss and influence of matrix composition on thermal shock resistance were studied.
研究了颗粒级配对显气孔率、体积密度、抗折强度、耐压强度、磨损量的影响以及基质组成对抗热震性的影响。 - The degree of crystallinity of pure PTFE reached maximum by air cooling and the abrasion loss also reached maximum among three ones;
纯聚四氟乙烯树脂在空气冷却时结晶度最大，磨损量也是三者中最大的； - Theory analysis and practice show ( 1) Define the parameter of power consumption and abrasion loss according the results of trial mill;
理论分析和实践证明，要根据试验磨的实验结果确定磨耗和功耗参数； - A bench test shows that compared with metal plunger couples, the abrasion loss of Si_3N_4 plunger couples has been 82%~ 91% lower, and their service life 8~ 11 times longer under the same experimental conditions.
台架试验结果表明：在相同试验条件下，与金属相比其磨损量降低了82%~91%，使用寿命提高了8~11倍。 - According to the analysis of the performance of antifriction by using abrasion tester, coefficient of friction and wear loss were measured on the conditions of regular feeding oil and no oil.
采用摩擦试验机对所制备的产物的抗磨性进行了表征分析；确定了正常供油状态下和无机油状态下，该纳米抗磨剂的摩擦因数及其磨损量。 - Under coexist condition of both corrosion and abrasion, the loss of layer metal mutually effected by both factors will be accelerated.
在腐蚀与磨损共存的条件下，两者协同作用加速材料流失。 - Some abrasion, such as that of generator shaft, bump shaft and drive shaft, will lead to great economic loss and harm.
大型轴件的损坏（如发电机转轴、水泵泵轴以及卷扬机传动轴的损坏）会造成重大经济损失与人身危害。 - The internal pressure strength and tensile strength of the casing inwall at the joints with various abrasion loss are calculated, and the relationship between the abrasion loss and the internal pressure factor and tensile factor of the casing joint is determined.
对套管接头处内壁不同磨损量时的抗内压强度和抗拉强度进行了计算分析，得出了磨损量与套管接头抗内压系数的定量数据和磨损量与套管接头抗拉系数的定量数据。 - The vulcanizate presented higher Shore A hardness, tensile strength, modulus at 100%, modulus at 300%, and elongation at break, and lower Akron abrasion loss;
硫化胶的邵尔A型硬度、拉伸强度、100%定伸应力、300%定伸应力及扯断永久变形增大，阿克隆磨耗量减小； - Abrasion not only consumes the energy and materials and decreases the equipment efficiency, but also accelerates the equipments discard and causes the parts replacement frequently and big economy loss.
磨损不仅消耗能源和花费材料、降低设备运转效率，而且加速设备报废、导致部件更换频繁，造成极大的经济损失。 - The abrasion wastage of port and mine machine is all through very large, and so it makes huge economic loss.
港口、矿山机械的易磨损件的消耗量一直很大，造成了巨大的经济损失。 - It was also suggested that the mechanism of the wear of PPS composites changed into particle abrasion and the wear loss increased when the nano-meter inorganic particle was used as filler.
纳米无机粒子的加入会使材料的磨耗量有所增大，其磨损机理转变为磨粒磨损。 - The abrasion loss of surface was the biggest when the impact angle of coal ash was 20 ℃.
当灰粒的冲击角度为20°左右时，灰粒对壁面的磨损量最大。 - Compared with the conventional shaft end seals, dry gas seal has many advantages including small leakage, little surface abrasion, low power loss, long service life and high reliability.
与传统的轴端密封相比，干气密封具有介质泄漏量少、端面磨损小、能耗低、运行寿命长和可靠性高等优点。 - Under dry friction condition, wear mechanism of ceramic are adhesive wear and abrasive wear. Abrasion loss of ceramic reduces with increasing of the sliding velocity and increases with increasing of the load.
在干摩擦条件下，陶瓷的磨损机理为粘着磨损与磨粒磨损；陶瓷的磨损量随着滑动速度的增加而降低，随着载荷的增加而增加。 - The relationship of abrasion loss and friction coefficient with respect to load, sliding velocity and sliding distance are discussed and wear mechanism of ceramic is analyzed.
对氧化铝陶瓷的耐磨损性能进行了检测与分析，讨论了载荷、滑动速度、滑动距离与磨损量、摩擦系数之间的关系，分析了陶瓷磨损过程机理。 - The wear rate of pin specimens without electric current shows a monotone increase with an increase in electric current. The wear mechanism is mainly attributed to adhesion and abrasion, oxidation and electric arc ablation loss.
有电流时，销试样的磨损率随电流的增加而增加，其摩擦面上有电弧烧蚀坑，同时伴有磨粒磨损，粘着磨损和氧化磨损。 - SBR abrasion loss decreased clearly when the carbon black contents increased.
提高炭黑用量丁苯橡胶的阿克隆磨耗损失明显减小。 - It was found by the study of Akron abrasion process that the abrasion loss of SBR vulcanizates at different stages was not the same.
阿克隆磨耗过程研究表明丁苯橡胶硫化胶在各个阶段的磨耗损失不一样。 - Abrasion is the one of the major reason for failure of material and mechanical equipments; it will cost great loss in economy and resource.
磨损是材料和机械设备失效的主要原因之一，会造成能源和材料的浪费，带来极大的经济和资源损失。 - All machinery motion is relative movement relying on its 'spares pairs. Abrasion happened with relative movement, and abrasion is the main cause of surface damage, spares invalid, and material friction loss.
所有机器的运动都是依赖其零件副的相对运动，有相对运动就有磨损，磨损是导致表面损坏、零件失效和材料损耗的主要原因。